Recent Topics
Walmart Oil Change?
by Talent_Keyhole - 01/18/20 12:50 AM
Bleh, mother’s gas furnace fan burned up
by Rmay635703 - 01/17/20 11:23 PM
Rotella gas truck vs Valvoline modern engine
by MoPowa - 01/17/20 09:25 PM
Afton Specification Handbook -- September 2019
by Gokhan - 01/17/20 09:04 PM
Old Retired Navy Commander
by KeithS_NW_Ohio - 01/17/20 08:58 PM
Mobil 1 EP vs Mobil 1 EP Truck & SUV
by jrommelt - 01/17/20 08:29 PM
Stick with Maxlife or go back to DW-1?
by jayjr1105 - 01/17/20 07:58 PM
Thread locker
by zzyzzx - 01/17/20 07:56 PM
A preppers tale
by Bluestream - 01/17/20 07:50 PM
19 Ram Rebel oil choices
by Schwifty - 01/17/20 07:35 PM
Is it impossible to get a loan for an older vehicle?
by FordBroncoVWJeta - 01/17/20 07:22 PM
Fridge and freezer oil test
by jkhawaii - 01/17/20 06:59 PM
Not on sale but theeeeeeyyyyy're here!
by jayjr1105 - 01/17/20 06:47 PM
Valvoline Daily Protection 5w30 - $13.52 at Walmart
by RonRonnster - 01/17/20 06:39 PM
Gotta love Friday
by 53' Stude - 01/17/20 06:11 PM
It was 1911
by CourierDriver - 01/17/20 06:10 PM
Desulfating a Battery
by 5AcresAndAFool - 01/17/20 05:41 PM
Newest Members
jonnyb433, kzbd, 54Robert, CPA1989, myisland
70463 Registered Users
Who's Online Now
25 registered members (blufeb95, Big O Dave, Char Baby, adams355, 5 invisible), 929 guests, and 12 spiders.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums67
Topics300,267
Posts5,172,019
Members70,463
Most Online3,728
Jan 11th, 2020
Donate to BITOG
Print Thread
Hop To
How to extract oil? #4884379 10/01/18 08:39 AM
Joined: Jan 2014
Posts: 516
S
Spetz Offline OP
OP Offline
S
Joined: Jan 2014
Posts: 516
Hi everyone,

I ordered a UOA kit that has a tube and a syringe to get the oil from the dipstick,

My questions are:
1. Does the oil need to be hot, engine running, engine just switched off, or cold is fine?
2. If the tube does not go down the dipstick what is another way I can get to the oil without draining it?
Can I remove the oil filter and extract some oil from there?
Or can I remove the oil cap and try to get some from the head?
3. The kit came with a 30cc syringe and a 100ml or so canister. Is 30cc enough for the lab or must I fill the canister?


2003 Mitsubishi Diamante 6G74. 165k miles.
Penrite HPR10 10W50, 12K km OCI
UOA:
https://www.bobistheoilguy.com/foru...ante-shu-5w40-1-2-can-mos2-7-8k-mile-oci
Re: How to extract oil? [Re: Spetz] #4884383 10/01/18 08:48 AM
Joined: Oct 2009
Posts: 5,841
JohnnyJohnson Offline
Offline
Joined: Oct 2009
Posts: 5,841
I would say it would be best to have just turned to engine off so things haven't settled out and are suspended in the oil.


2004 Corolla 138272
Out: Havoline Pro DS 10w-30 Purolator PureOne 10-29-19 136457
In: Pennzoil Platinum HM 5W-20 ST 4386
2006 Duramax 77060
Out: T6 5W-40 XG9100 73909
In: Rotella Dino PH9100 11-3-19
Re: How to extract oil? [Re: Spetz] #4884390 10/01/18 08:59 AM
Joined: Apr 2010
Posts: 4,464
B
BMWTurboDzl Offline
Offline
B
Joined: Apr 2010
Posts: 4,464
Engine warm not hot nor cold. Maybe sample an 30 mins or so after you've driven it. The idea is that any solids will remain uniformly distributed in the oil and not have settled at the bottom of the pan.


You could reach out to Blackstone Labs. They may have suggestions on how to sample.


“It took untold generations to get you where you are. A little gratitude might be in order. If you’re going to insist on bending the world to your way, you better have your reasons.”

435i
Re: How to extract oil? [Re: Spetz] #4884432 10/01/18 10:08 AM
Joined: Aug 2008
Posts: 25,017
StevieC Offline
Offline
Joined: Aug 2008
Posts: 25,017
When I do sampling and not complete changes at the time of a UOA collection, I like to make sure the vehicle has been run somewhere like shopping etc. I return home, let the vehicle cool a little and then I send the tube on my collection pump down the dipstick tube. I have found that lubricating the outside of the tube with clean engine oil makes it go down the tube much easier. I always dump the first bit of extracted oil back into the engine via the oil cap in case there was residuals in the tube/pump from the last extraction. Then on the second extraction I pump this into my bottle to be sent to the lab.


'18 Caravan - 48k KM - AMSOIL SS 0w20, Fram Ultra, TC-W3 500:1
'06 Santa Fe - 535k KM (Retired)

There is no such thing as "lifetime" fluids! mad
Re: How to extract oil? [Re: Spetz] #4884445 10/01/18 10:22 AM
Joined: May 2009
Posts: 14,149
A
ARCOgraphite Offline
Offline
A
Joined: May 2009
Posts: 14,149
Sounds like the plan! /\ /\ /\

Last edited by ARCOgraphite; 10/01/18 10:22 AM.

2019 VW Jetta S 6MT OCI#2 7378mi-MOTUL Specific VW508.00+VW Service Filter; '17 Subaru Crosstrek CVT OC#8 60864mi-Subaru Idemitsu 0W20 + SOA Filter
Re: How to extract oil? [Re: Spetz] #4884704 10/01/18 03:33 PM
Joined: Oct 2010
Posts: 1,907
D
Danh Offline
Offline
D
Joined: Oct 2010
Posts: 1,907
Just one more small suggestion: Mark the extraction tubing at a point where it equals the length of the dipstick. This will ensure you extract oil from a good midpoint and don’t reach the bottom of the sump where crud could have settled and accumulated.

Re: How to extract oil? [Re: Spetz] #4884847 10/01/18 05:57 PM
Joined: Oct 2014
Posts: 702
I
Ihatetochangeoil Offline
Offline
I
Joined: Oct 2014
Posts: 702
1. Does the oil need to be hot, engine running, engine just switched off, or cold is fine?
Answer per Blackstone: https://www.blackstone-labs.com/gas-sampling.php Answer per me: I take my samples from a hot, running engine; but I have bypass filters with a sampling petcock; it's pretty easy and mess free. I wear leather TIG welding gloves in case of accidental contact with hot engine parts. To sample from my son's car, (no petcock), I remove the oil filler cap (with the hot motor idling) and carefully insert the sampling tube into a "puddle" of oil in a low area cast into the cylinder head; it may take several "draws" and a few minutes to get enough oil for the sample bottle.

2. If the tube does not go down the dipstick what is another way I can get to the oil without draining it? Answer per me: You can also loosen the oil filter a little and catch some oil, I've done this with a clean spare glass beaker and then poured it into the sampling bottle, but I would NOT attempt this on a running engine!!! I let the engine run long enough to reach equilibrium temperature; chock, jack and support the car, then shut the engine down and immediately get my sample. Job 1 is to be very cautious, be safe, don't get burned. A splash in the face with hot oil is not funny; I wear safety glasses, a full face polycarbonate grinding shield and a leather welding jacket. Never been burned and don't plan on it. Who does?

3. The kit came with a 30cc syringe and a 100ml or so canister. Is 30cc enough for the lab or must I fill the canister? Answer: Blackstone says they need 3 oz; which works out to about 90 ml. https://www.conversion-metric.org/volume/ounce-to-milliliter

Re: How to extract oil? [Re: Spetz] #4884880 10/01/18 06:29 PM
Joined: Sep 2010
Posts: 11,401
4WD Offline
Offline
Joined: Sep 2010
Posts: 11,401
For large industrial engines the sump is a no-no and samples are taken from the cooler loop (sample valve) …

Re: How to extract oil? [Re: Spetz] #4927464 11/18/18 07:49 AM
Joined: Jul 2003
Posts: 3,118
J
jorton Offline
Offline
J
Joined: Jul 2003
Posts: 3,118
Do you think I can get a sample from the dipstick tube on a CVT? I think the tube makes a right angled turn at the attachment to the transmission.


"If everything seems under control, you're just not going fast enough."
- Mario Andretti


Previous Thread
Index
Next Thread

BOB IS THE OIL GUY® Powered by UBB.threads™