found out today that their additive gashol oil treatment has bismuth in an all synthetic formula
SFR with Bismuth
- Thread starter boxcartommie22
- Start date
- Status
MolaKule
Staff member
And SFR iS?
And Bismuth does what?
And Bismuth does what?
I was thinking PeptoBismal - butt that would just start a bunch of bad gut jokes.
mola, you tell us what kind of additive that has bismuth as one of their ingredient
This product I know about from personal usage.
With the SFR gas additive product and the SFR engine additive used in 2005 Corolla went from average of 35.3 mpg to 39.3 mpg average last 8 tankfulls. (Before and after treatment - Amsoil 5w-30).
Below is a listing of ASTM testing done that I have compiled on product.
ASTM-D-2783 Standard Method for MEASUREMENT OF EXTREME-PRESSURE PROPERTIES OF LUBRICATING FLUIDS (FOUR-BALL METHOD)
Testing Laboratory: Southwest Research Institute (SWRI) in San Antonio, Texas
1. This method covers the determination of the load-carrying properties of lubricating fluids. The following two determinations are made:
i. Load-wear index and
ii. Weld point by means of the four-ball extreme-pressure (EP) tester
ASTM-D-6335-98 STANDARD TEST METHOD FOR DETERMINATION OF HIGH TEMP. DEPOSITS BY THERMO-OXIDATION ENGINE OIL SIMULATION TEST
Testing Laboratory: Southwest Research Institute (SWRI) in San Antonio, Texas
Date Completed: 2/14/2001
American Society for Testing and Materials ASTM KA24E Nissan Valve Train Wear Test
Testing Laboratory: Lubrizol Laboratories in Wickliffe, Ohio.
Date Completed 9/25/02
The results of the test indicate that when SJ rated Pennzoil 10W30 engine oil was treated at 5%
by volume with SFR 100 and subjected to the KA24E test; average camshaft lobe wear was reduced
from 41.43 microns to 35.62 microns, a reduction of 14%.
ASTM-D-6557-00 STANDARD TEST METHOD FOR EVALUATION OF RUST PREVENTIVE CHARACTERISTICS OF AUTOMOTIVE ENGINE OILS
Testing Laboratory: Southwest Research Institute (SWRI) in San Antonio, Texas
Date Completed: 1/16/2001
Test considered Valid-PASS; Fresh Ball Gray Value SOT:
134, EOT: 134. Average Gray Value for ProTecta® Engine Treatment: 119.
Compatible with petroleum, mineral, and synthetic motor oils and oil additives.
Will not void new vehicle warranties.
Contains no chlorinated paraffins, PTFE resins, "moly" or graphite.
8-Year/200,000 Mile Engine Warranty if used before vehicle reaches 40k.
Website of local distributor.
http://www.ersonline.biz/sfradd1.html
With the SFR gas additive product and the SFR engine additive used in 2005 Corolla went from average of 35.3 mpg to 39.3 mpg average last 8 tankfulls. (Before and after treatment - Amsoil 5w-30).
Below is a listing of ASTM testing done that I have compiled on product.
ASTM-D-2783 Standard Method for MEASUREMENT OF EXTREME-PRESSURE PROPERTIES OF LUBRICATING FLUIDS (FOUR-BALL METHOD)
Testing Laboratory: Southwest Research Institute (SWRI) in San Antonio, Texas
1. This method covers the determination of the load-carrying properties of lubricating fluids. The following two determinations are made:
i. Load-wear index and
ii. Weld point by means of the four-ball extreme-pressure (EP) tester
ASTM-D-6335-98 STANDARD TEST METHOD FOR DETERMINATION OF HIGH TEMP. DEPOSITS BY THERMO-OXIDATION ENGINE OIL SIMULATION TEST
Testing Laboratory: Southwest Research Institute (SWRI) in San Antonio, Texas
Date Completed: 2/14/2001
American Society for Testing and Materials ASTM KA24E Nissan Valve Train Wear Test
Testing Laboratory: Lubrizol Laboratories in Wickliffe, Ohio.
Date Completed 9/25/02
The results of the test indicate that when SJ rated Pennzoil 10W30 engine oil was treated at 5%
by volume with SFR 100 and subjected to the KA24E test; average camshaft lobe wear was reduced
from 41.43 microns to 35.62 microns, a reduction of 14%.
ASTM-D-6557-00 STANDARD TEST METHOD FOR EVALUATION OF RUST PREVENTIVE CHARACTERISTICS OF AUTOMOTIVE ENGINE OILS
Testing Laboratory: Southwest Research Institute (SWRI) in San Antonio, Texas
Date Completed: 1/16/2001
Test considered Valid-PASS; Fresh Ball Gray Value SOT:
134, EOT: 134. Average Gray Value for ProTecta® Engine Treatment: 119.
Compatible with petroleum, mineral, and synthetic motor oils and oil additives.
Will not void new vehicle warranties.
Contains no chlorinated paraffins, PTFE resins, "moly" or graphite.
8-Year/200,000 Mile Engine Warranty if used before vehicle reaches 40k.
Website of local distributor.
http://www.ersonline.biz/sfradd1.html
- Status
