Recent Topics
2018 Ford Edge Oil Question
by Passport1 - 03/29/20 04:52 PM
Help school an engineer
by DriveHard - 03/29/20 04:47 PM
Broken sway bar bolt
by HoosierJeeper - 03/29/20 04:00 PM
can I use it?
by avi1777 - 03/29/20 03:54 PM
Service Champ OF2222 75% OLM, unknown miles
by bullwinkle - 03/29/20 03:50 PM
Gas Buddy Question
by Wolfshead - 03/29/20 03:30 PM
Caliper piston boot
by painfx - 03/29/20 03:25 PM
Graphene the next detailing protection
by Mamala Bay - 03/29/20 02:17 PM
Anyone here a blacksmith?
by 53' Stude - 03/29/20 02:13 PM
Buying products made outside the USA
by 007 - 03/29/20 01:22 PM
Marine oils on sale at Canadian Tire
by Snagglefoot - 03/29/20 12:42 PM
0W16 instead of 0w20?
by Mter00s - 03/29/20 12:36 PM
XG10575 Walmart.com deal
by 762fermeandyou - 03/29/20 12:29 PM
Virgin ACDelco PF1245 cut and post
by nwjones18 - 03/29/20 11:49 AM
Oups, forgot oil cap...
by M119 - 03/29/20 11:46 AM
Recommendation for tuned BMW N55?
by RIPGermanCastrol - 03/29/20 11:15 AM
Electrician's Help With Circuit Breaker ?
by doitmyself - 03/29/20 11:07 AM
Get your physicals done people
by BeerCan - 03/29/20 08:41 AM
2004 Silverado
by mjk - 03/29/20 08:29 AM
Shimmy on the Hiwy
by Char Baby - 03/29/20 06:06 AM
Newest Members
yulichris, jeff58, jimmyturner, ChainsawGuy, jbr
71038 Registered Users
Who's Online Now
101 registered members (77GrandPrix, 2010Civic, 2oldtommy, 2K2AcuraTL, 53' Stude, alphadog, 10 invisible), 1,997 guests, and 20 spiders.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums67
Topics303,324
Posts5,233,934
Members71,038
Most Online4,538
Jan 20th, 2020
Donate to BITOG
Print Thread
Hop To
Hydraulic Fluid Change Question #5384040 03/23/20 08:05 PM
Joined: Sep 2007
Posts: 314
L
lancerplayer Offline OP
OP Offline
L
Joined: Sep 2007
Posts: 314
I have a new to me John Deere Z445 zero turn mower. I would like to do some basic maintenance on it before the mowing season. I plan to change the engine oil and filter, air filter, fuel filter, spark plugs, and transaxle hydraulic fluid.

Fluid spec: John Deere Low Viscosity HY-GARD® (J20D)

My question is: following the manufacturer's procedure, will I have to be concerned with any air getting into the hydraulic system? Will I have to purge the system?


1. Park machine safely on a level surface.

2. Raise operator’s seat, and clean area around reservoir cap. Remove cap.

3. Clean area around hydraulic oil filter.

4. Place drain pan with at least a 9.9 L (10.5 qt) capacity under hydraulic oil filter, turn filter counterclockwise to remove and allow oil to drain completely.

5. Apply a film of clean oil on gasket of new filter.

6. Install filter. Turn filter clockwise until gasket makes contact with the mounting surface. Tighten 1/2 to 3/4 turn after gasket contact.

NOTE: Reservoir capacity is approximately 8.5 L (9 qt). Total system capacity with filter is approximately 9.9 L (10.5 qt).

7. Fill oil reservoir with approximately 8.5 L (9 qt) of oil.

8. Install reservoir cap.

9. Start engine.

10. Move throttle lever to the 3/4 fast idle position.

11. Unlock park brake.

12. Run engine in full forward position for five minutes and then cycle motion control levers forward and rearward several times. Check for leaks around filter.

13. Stop the engine. Check oil level in reservoir. Add oil as necessary.



Re: Hydraulic Fluid Change Question [Re: lancerplayer] #5384070 03/23/20 08:52 PM
Joined: Jun 2003
Posts: 90
S
samven Offline
Offline
S
Joined: Jun 2003
Posts: 90
That is their purge method. The running for 5 min in forward just heats up the hydraulic fluid to normal operating temps then the cycle of forward reverse purges any air in the system. On my tractor after a fluid change I do similar. Idle system for 5 min then run tractor in forward for several min then cycle the front end loader up and down bucket in and out looking for jerky movement. Run PTO and lift and lower mid deck several times.

Re: Hydraulic Fluid Change Question [Re: lancerplayer] #5384710 03/24/20 03:49 PM
Joined: Aug 2003
Posts: 12,442
J
JTK Offline
Offline
J
Joined: Aug 2003
Posts: 12,442
Not sure what drive system this JD uses, but on most of them, after the refill, you pull the bypass lever on the drive, start the engine and cycle the controls forward-reverse a few times to purge the air out. If it's a separate hydraulic pump and motor drive, air will typically work it's way through the system.


2019 Nissan Pathfinder SV
2017 Ram 1500 4x4, 3.6L.
2015 Nissan Versa 1.6 S
Previous Thread
Index
Next Thread

BOB IS THE OIL GUY® Powered by UBB.threads™