Recent Topics
I have sinned
by 901Memphis. 12/15/18 01:57 PM
Milwaukee m12 in vanhaus ratchet
by pda1122. 12/15/18 01:19 PM
Klein dikes
by Donald. 12/15/18 01:03 PM
Help Soldering 3.5mm mono microphone plug
by Brybo86. 12/15/18 01:02 PM
Small Trolling Motors
by wings&wheels. 12/15/18 12:49 PM
Toyota Corolla, good and bad?
by jongies3. 12/15/18 12:35 PM
Mixing oils
by bfleeman. 12/15/18 10:51 AM
Ebay 10% off Tech 15% off everything else*.
by demarpaint. 12/15/18 10:39 AM
Milwaukee Fuel M12 Ratchet 1/4” vs 3/8”
by Snagglefoot. 12/15/18 10:16 AM
Hifly Hf 805
by chrisri. 12/15/18 10:00 AM
Preferred 5.3L L83 Oil Filter
by zfasts03. 12/15/18 09:58 AM
sonata plastic fork starter failed three times.
by JustinH. 12/15/18 09:17 AM
HVAC Problems
by WTJackalope. 12/15/18 09:15 AM
Rough Idle after short trip
by Datarock. 12/15/18 09:07 AM
Homelite 360
by mobilaltima. 12/15/18 09:04 AM
Lovin' the Etec!
by IndyFan. 12/15/18 06:10 AM
Air Impact Wrench
by BenZahel. 12/15/18 05:19 AM
Luber finer 750 bypass oil filter info
by BigRich954. 12/15/18 03:59 AM
Ford Pickup Front Wheel Bearings 2WD
by benjamming. 12/14/18 10:52 PM
Newest Members
Spkrdctr, torchredone12, JNG, Edmundo, NEKGuy
66688 Registered Users
Who's Online Now
69 registered members (77GrandPrix, anndel, andyd, 71Chevyguy, aba4430, 11 invisible), 1,824 guests, and 37 spiders.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums67
Topics295,112
Posts4,927,982
Members66,688
Most Online2,553
Oct 27th, 2018
Donate to BITOG
Previous Thread
Next Thread
Print Thread
Hop To
Page 1 of 2 1 2
Wix oversize filter options - 20X1.5mm thread #331075
12/05/04 05:37 PM
12/05/04 05:37 PM
Joined: Oct 2004
Posts: 140
Atlanta
Michael Polutta Offline OP
Michael Polutta  Offline OP
Joined: Oct 2004
Posts: 140
Atlanta
I asked some filter size questions of Wix via email. In response they sent me their Master Catalog! Here are the oversize filter options I've been able to discern for the 20X1.5mm thread size. Here's hoping this formats correctly.

At my next Odyssey oil change I will be checking to see if the 2.834/2.462 gasket seals properly. It does on my '89 Mazda MX-6 GT. The Wix 51182 is HUGE! I bought one to try from O'Reilly yesterday for $11. I've been using the Purolator 20253 on my Mazda for a while with good results. The Wix 51324 is the equivalent.

code:
 Purolator 	Wix	Bosch	Mobil 1	Height	Diameter	Bypass	Gasket Inner	Gasket Outer	ADBV	Size/Vol
14619 51626 3.812 3.663 8-11 2.462 2.834 yes 40.17146094
20073 51347 4.828 2.921 8-11 2.43 2.734 yes 32.35350021
14610 51356 3.402 2.685 8-11 2.173 2.475 yes 19.26255032
24458 51344 4.069 3.242 8-11 2.2 2.49 yes 33.58958265
20253 51324 3401 M1-207 4.354 3.663 16 2.462 2.834 yes 45.88314295
14459 51334 3.194 3.252 8-11 2.173 2.475 yes 26.52936669
51568 4.072 3.324 16 2.173 2.475 yes 35.33626934
51182 5.207 3.66 24 2.462 2.834 yes 54.78234838
51285 5.811 2.967 30 2.37 2.74 NO 40.17694079


Re: Wix oversize filter options - 20X1.5mm thread #331076
12/05/04 07:44 PM
12/05/04 07:44 PM
Joined: Oct 2004
Posts: 140
Atlanta
Michael Polutta Offline OP
Michael Polutta  Offline OP
Joined: Oct 2004
Posts: 140
Atlanta
BTW, I just looked up the Purolator xref to the 51182 (the REALLY BIG one). L34480 is the number, and this one has a 15psi bypass setting.

Re: Wix oversize filter options - 20X1.5mm thread #331077
12/06/04 08:26 AM
12/06/04 08:26 AM
Joined: Dec 2003
Posts: 12,385
Northern CA
XS650 Offline
XS650  Offline
Joined: Dec 2003
Posts: 12,385
Northern CA
quote:
Originally posted by Michael Polutta:
Here's hoping this formats correctly.


Nice data. That stuff is hard to find in one place. Thanks.

Hope you don't mind, I think this will format a bit better.
code:
 
Purolator Wix Bosch Mobil 1 Height Dia. Bypass G.In G.Out ADBV Vol(in^3)
14619 51626 3.812 3.663 8-11 2.462 2.834 yes 40.2
20073 51347 4.828 2.921 8-11 2.43 2.734 yes 32.4
14610 51356 3.402 2.685 8-11 2.173 2.475 yes 19.3
24458 51344 4.069 3.242 8-11 2.2 2.49 yes 33.6
20253 51324 3401 M1-207 4.354 3.663 16 2.462 2.834 yes 45.9
14459 51334 3.194 3.252 8-11 2.173 2.475 yes 26.5
51568 4.072 3.324 16 2.173 2.475 yes 35.3
51182 5.207 3.66 24 2.462 2.834 yes 54.8
51285 5.811 2.967 30 2.37 2.74 NO 40


Re: Wix oversize filter options - 20X1.5mm thread #331078
12/06/04 08:31 AM
12/06/04 08:31 AM
Joined: Oct 2004
Posts: 140
Atlanta
Michael Polutta Offline OP
Michael Polutta  Offline OP
Joined: Oct 2004
Posts: 140
Atlanta
XS650 - thanks for the reformat. What was the "trick"?

If anyone needs a different thread size chart, I'll be happy to work on it as I have time. Just let me know...

Michael

Re: Wix oversize filter options - 20X1.5mm thread #331079
12/06/04 08:44 AM
12/06/04 08:44 AM
Joined: Dec 2003
Posts: 12,385
Northern CA
XS650 Offline
XS650  Offline
Joined: Dec 2003
Posts: 12,385
Northern CA
quote:
Originally posted by Michael Polutta:
XS650 - thanks for the reformat. What was the "trick"?


Tabs can cause problems when going from one medium to another. I replaced a bunch of them with spaces. The only tabs that really needed to be replaced were in your top line with the column titles.

Re: Wix oversize filter options - 20X1.5mm thread #331080
12/08/04 05:04 AM
12/08/04 05:04 AM
Joined: Sep 2002
Posts: 622
42.4N 85.7W
n8wvi Offline
n8wvi  Offline
Joined: Sep 2002
Posts: 622
42.4N 85.7W
If you'd like more options (some with very similar dimentions, some much larger) AND better availability (like the FL-1A for instance), you could change the filter threads to 3/4x16 while keeping the M20x1.5 threads in your block. I did it to my Subaru and I'm using the Purolator PL20195 (FL-400 equiv). I've described how I did it here on BITOG. If you had the room you could then use the 6.9 inch by 3.78 inch Purolator 40017. Now THAT'S a big filter [Big Grin]

Dave

Re: Wix oversize filter options - 20X1.5mm thread #331081
12/08/04 06:27 AM
12/08/04 06:27 AM
Joined: Oct 2004
Posts: 140
Atlanta
Michael Polutta Offline OP
Michael Polutta  Offline OP
Joined: Oct 2004
Posts: 140
Atlanta
With the volume of the Wix 51182 / Purolator 34480 I'm not all that concerned about bigger filters. However, I am curious about the source for your Mopar part number. Google only comes up with your BITOG page!

Where'd you get it?

Re: Wix oversize filter options - 20X1.5mm thread #331082
12/08/04 04:35 PM
12/08/04 04:35 PM
Joined: Sep 2002
Posts: 622
42.4N 85.7W
n8wvi Offline
n8wvi  Offline
Joined: Sep 2002
Posts: 622
42.4N 85.7W
It was a Jeep forum somewhere...... I really don't remember. I googled 20x1.5 AND 3/4x16. IIRC, it was part of an oil cooler setup that someone had documented.

I understand you may not want something larger than what's available w/ 20x1.5, this would just give you the alternative of easier to find part numbers like the Purolator 20195 or 30001.

<Edit> I just re-read your last post. Did you mean where did I purchase it? That I do remember, at the local Jeep dealer.

Dave

Re: Wix oversize filter options - 20X1.5mm thread #331083
12/08/04 06:05 PM
12/08/04 06:05 PM
Joined: Jul 2003
Posts: 1,130
California
jthorner Offline
jthorner  Offline
Joined: Jul 2003
Posts: 1,130
California
quote:
change the filter threads to 3/4x16 while keeping the M20x1.5 threads in your block
Personally I would not go that route because if anyone else ever attempts to maintain the car they are going to find that the standard filter for the vehicle doesn't work.

John

Re: Wix oversize filter options - 20X1.5mm thread #331084
12/09/04 08:57 AM
12/09/04 08:57 AM
Joined: Sep 2002
Posts: 622
42.4N 85.7W
n8wvi Offline
n8wvi  Offline
Joined: Sep 2002
Posts: 622
42.4N 85.7W
I've considered that, but the only way that would happen is if I were hit by a bus [Big Grin] NO ONE does routine maint. on my car except myself. Besides, if for some unimaginable situation where someone else was changing my filter, they'd just put on whatever flavor filter they sell that crosses to the PL20195 I've got on there now.

Dave

Re: Wix oversize filter options - 20X1.5mm thread #331085
12/08/04 09:11 PM
12/08/04 09:11 PM
Joined: Dec 2003
Posts: 12,385
Northern CA
XS650 Offline
XS650  Offline
Joined: Dec 2003
Posts: 12,385
Northern CA
quote:
Originally posted by n8wvi:
I've considered that, but the only way that would happen is if I were hit by a bus [Big Grin] NO ONE does routine maint. on my car except myself. Besides, if for some unimaginable situation where someone else was changing my filter, they'd just put on whatever flavor filter they sell that crosses to the PL20195 I've got on there now.

Dave

Dave, Just be aware that a 20x1.5mm might screw onto the 3/4-16 spud by hand. It would be severly lacking in thread engagement.

Re: Wix oversize filter options - 20X1.5mm thread #331086
12/09/04 11:37 AM
12/09/04 11:37 AM
Joined: Jul 2003
Posts: 1,130
California
jthorner Offline
jthorner  Offline
Joined: Jul 2003
Posts: 1,130
California
quote:
just put on whatever flavor filter they sell that crosses to the PL20195 I've got on there now
Most shops go by what their computer says should be on the car rather than by crossing whatever is on there now. Also, the metric and SAE threads are close enough that an unaware person might think they were doing OK putting the wrong thing on.

Certainly if you ever sell the car it would be a nice move to put it back to the original configuration.

John

Re: Wix oversize filter options - 20X1.5mm thread #331087
12/09/04 04:03 PM
12/09/04 04:03 PM
Joined: Sep 2002
Posts: 622
42.4N 85.7W
n8wvi Offline
n8wvi  Offline
Joined: Sep 2002
Posts: 622
42.4N 85.7W
OK OK OK!!! Like I said, NO ONE does routine maint. on my car except myself And yes, I've kept the original part. Jheesh! You'd think I'd mixed Redline w/ AutoRX or called someone a name. I was just offering an alternative.

Happy Chanukkah everyone [Cheers!]

Dave

Re: Wix oversize filter options - 20X1.5mm thread #331088
12/11/04 09:24 AM
12/11/04 09:24 AM
Joined: Nov 2004
Posts: 17
Big Spring TX
nemir Offline
nemir  Offline
Joined: Nov 2004
Posts: 17
Big Spring TX
I removed conector from 2.6 Dodge [Mitsubishi],it was about 3" long had local machine shop make new one metric combo SAE cost 15.00 instaled with B2 Baldwin and 10/30 M1. Works great. This is a $6 savings between the B2 and a Wix 51182. Thanks for the Idea. NEMIR

Re: Wix oversize filter options - 20X1.5mm thread #331089
12/11/04 10:33 PM
12/11/04 10:33 PM
Joined: Sep 2002
Posts: 622
42.4N 85.7W
n8wvi Offline
n8wvi  Offline
Joined: Sep 2002
Posts: 622
42.4N 85.7W
Your welcome [Cheers!] $15 is less than what I would have guessed for a custom part. I think the Mopar part I bought was around $8.

Dave

Page 1 of 2 1 2

BOB IS THE OIL GUY® Powered by UBB.threads™