Search results

They generally work but are huge heavy clunky guns, All that cast zinc. Never would own one, Too many good guns out there that are not very expensive.

Motor oil works just fine on guns. I don't use it to clean guns just lubricate. A quart of Mobil 1 will last the rest of your life and your kids. Most gun oils are nothing special and the tales are that one is nothing but repackaged Mobil 1 and the other trendy one is coconut oil with a few...

Balistol is also water based and can be used to clean a gun after shooting corrosive ammo or black powder. This is mostly what I use it for as I have quite a bit of Russian and Chinese corrosive ammo as well as some others.

The extra weight and action of the gas on the compensator help slow the slide down. I would expect the kit comes with a heavier recoil spring as well. A heavier hammer sporing can also be used to help slow and delay the slide. The .460 works and you'll note you can not buy a conversion without...

The 1-6X or 1-8X power scopes will do it all. If they are a true 1X power get one with an illuminated reticle and you can shoot from zero to farther than a 5.56 is effective. Trijicons are great but fixed power and if you're older like me they don't work without wearing readers as they have no...

I'll use it in my 2017 Ram 2500 6.7 Cummins and I use it in several other applications including my Polaris quads. Thanks for the information. that's the price they sell it for all the time. Priced like the syn blend. I'm going to start using it!

I've found some info here on BITOG about Mystic 15W40 in both standard and syn blend but virtually nothing on the full synthetic HDEO with a CJ4 rating. Any experience out there? Price is real good at the local ranch store at $15.00 a gallon jug.

Simplistic, I was wondering about replacing the pressure relief valve if necessary if it goes through the front cover and how difficult it was to access. Originally Posted By: simplistic Yes, the relief Is in the front cover. However you do not check the pressure there. You remove the sending...

I have been busy but finally got around to swapping back to Mobil 1 TDT and my normal filter. Pressure will still hit 90+PSI at high RPM. Have to hunt down someone with a mechanical gauge to verify my stock gauge. I have found one parts drawing showing the pressure relief valve on an LB7. It...

Simplistic, That's what I have been seeing consistently for the life of the truck. I have replaced all the stepper motors and it seems to be working fine but I do not have a tech 2 tool. As I have said this happened immediately after the oil change. I guess we'll see if there is a difference...

All was fine prior to the oil change noticed higher pressure immediately thereafter. I guess it could break between shutting it off and starting it up but I kind of doubt it.

Update: I towed my 5th wheel up to Mammoth CA. and the oil pressure went nuts! Pulling out of Bishop up 395 I had to climb the Sherwin grade. As I went up I noticed the pressure was high but didn't have my glasses on. I popped them on and the needle was pegged! It hit 120+ PSI pulling the grade...

Originally Posted By: simplistic I then have to ask what was your previous oil and filter. Since we have the same engine, if you're 2 marks higher on the gauge then you have increased your op by 30psi. That raises some red flags to have an op increasse that much. If you are talking hot op...

Simplistic, Like I said mine is very consistent and this has not happened before so I suspect either the oil or the filter and wondering if anyone has noticed the same phenomena with either the oil or filter I am using.

No it doesn't use any oil. It has been very consistent in it's pressure readings since new. Some oils I have tried ran a little less pressure but nothing has run higher pressure, especially when hot from towing than Mobil 1.

I just changed over to Delo synthetic in my 2003 Chevy 2500HD Duramax. It's running about 2 ticks higher oil pressure on the gauge that Mobil TDT did. Only other thing different is I used a new Fram synthetic media filter. Thoughts?

I ran RP 15W40 when I couldn't find Mobil 1 Turbo Diesel Truck. I did notice that RP did not hold oil pressure as well as Mobil 1. Other than that it seemed fine.

Probably handloaded his ammo and double charged a case. If it was factory amo I am certain he would have been complaining about it!

I use it in my high powered rifles. Yes I ahve run copper remover through afterwards and it does work very well. I was really suprised at how well it works! No effort, fast and no nasty smell either.

My error guys it's Gunslick foaming bore cleaner not Outers!!!!! You'll have to kill me later! My memory is getting way to short!