Recent Topics
The ideal xW oil
by Nick1994
17 minutes 52 seconds ago
Things to do in Canada?
by dlundblad
20 minutes 42 seconds ago
Troubling UOA?
by EastCoastHD
28 minutes 19 seconds ago
Pennzoil PP Ultra 0w-20
by asharris7
34 minutes 3 seconds ago
WebMD
by Eddie
Today at 03:20 PM
Fox Mustang Heater Core Issues-Stop-leak work?
by Striker
Today at 02:29 PM
Rust removal followed by LineX.
by RamFan
Today at 02:25 PM
cartridge oil filters
by sourkraut
Today at 02:03 PM
Rear axle fluid change completed at 23,680 miles
by gonefishing
Today at 01:56 PM
Is it possible to make a low SAPS w20?
by badtlc
Today at 12:02 PM
Napa Proselect 21348 Cut open
by Brybo86
Today at 10:10 AM
Apple stops unlocking devices for police
by Volvohead
Today at 10:02 AM
Newest Members
EastCoastHD, ckwhite, borrellimd, biewabbeljoe, waynesworld
51334 Registered Users
Who's Online
89 registered (andyd, 95MarkVIII, 01rangerxl, 123Saab, 1 FMF, 901Memphis, 5 invisible), 1774 Guests and 203 Spiders online.
Key: Admin, Global Mod, Mod
Forum Stats
51334 Members
64 Forums
219426 Topics
3462797 Posts

Max Online: 2862 @ 07/07/14 03:10 PM
Donate to BITOG

Topic Options
#3321785 - 03/24/14 09:35 AM Oil for Engine Driven Welder
IntIron Offline


Registered: 04/08/07
Posts: 1
Loc: CO
Hello,

We run Kohler Commander engines, air cooled. The recommended interval is 100 hours for oil and 150 for Oil Filter.

We have been running Mobil 1, Full Synthetic 10W-30 and just putting the interval at 150 for each.

Do you think this is ok?

Thank you.

Top
#3321797 - 03/24/14 09:47 AM Re: Oil for Engine Driven Welder [Re: IntIron]
Oil Changer Offline


Registered: 08/28/06
Posts: 1390
Loc: Detroit Metro
I had a Miller Bobcat and we used Rotella SAE30 in SoCal. M1 is fine but I would use the HM version. The HM is A3/B3 and much heavier with an HTHS of 3.5 as opposed to the 3.0 of what you are currently using. The HM also has more Z and Ph. As a total package, go with the HM if M1 is cheap and easy to get.

Having said all of that, T5/T6, SAE30/40 HDEO will work just fine.

Top
#3321846 - 03/24/14 10:36 AM Re: Oil for Engine Driven Welder [Re: IntIron]
440Magnum Offline


Registered: 02/01/09
Posts: 6246
Loc: Texas
I tend to run Rotella T6 (5w40 synthetic) in all my OPE. No complaints, the last one I had to open up (non oil-related problem) was absolutely spotless inside. Bore and bearings all looked great. Most OPE now seems to call for an Xw30, but I've never had a problem going to T6 even though its an Xw40- cold starts (relatively speaking- we don't have much below 20F nights here, and only a few times a year) are not an issue thus far. And it makes me feel a little more secure on the 100+ F summer days.
_________________________
'66 Dodge Polara & '69 Dodge Coronet R/T both 440/727
'08 Ram 1500 4.7/545RFE
'12 Challenger SRT8 392/6-speed
'99 Cherokee 4.0, '11 Grand Cherokee 3.6

Top
#3322036 - 03/24/14 01:07 PM Re: Oil for Engine Driven Welder [Re: IntIron]
Doog Offline


Registered: 10/24/11
Posts: 3450
Loc: Ohio
Rotella T5 10w30 will do just fine.
_________________________
The difference between a beer and your opinion is that I asked for a beer...

Top
#3322628 - 03/24/14 11:19 PM Re: Oil for Engine Driven Welder [Re: IntIron]
Doug Hillary Online   content


Registered: 05/30/03
Posts: 4838
Loc: Airlie Beach Australia
Hi,
Intiron - Welcome to BITOG

What you have been doing is just fine - keep doing it with confidence
_________________________
Regards
Doug

Top
#3344686 - 04/16/14 03:20 PM Re: Oil for Engine Driven Welder [Re: IntIron]
tig1 Offline


Registered: 01/03/09
Posts: 9801
Loc: Illinois
For gas powered welders like yours M1 10-30 is a good choice. I use this oil in all my OPE including my 5KW gen.
_________________________
2007 Ford Fusion 142,000 miles
M1 0-20
2007 Ford Focus 127,000 miles
M1 0-20
10,000 mile OCIs on both engines
M1 ATF
M1 10-30 in all OPE

Top
#3352006 - 04/24/14 02:04 PM Re: Oil for Engine Driven Welder [Re: IntIron]
camelCase Offline


Registered: 07/11/13
Posts: 168
Loc: Southeastern, USA
I'd run Rotella T6. The 5W40 will give you the cold start pumpability but will have a thicker oil film on the higher end. Portable engines typically don't have the tightest tolerances and wear pretty weirdly sometimes. The 40wt is just 1 step higher, but can greatly increase the oil wedge's load holding capacity.

Plus - it's hard to beat the bang for buck value fo Rotella T6.

Top
#3377327 - 05/21/14 12:07 PM Re: Oil for Engine Driven Welder [Re: IntIron]
bulwnkl Offline


Registered: 02/09/05
Posts: 1442
Loc: Arizona
We ran Kendall Super-D III in our Lincoln Ranger 9s for a very long time. When I was operating in Yuma and Kendall was not reasonably available, I put in an alternative, high-quality 15W40 all-fleet oil. Those Ranger 9s never smoked or had any troubles at all, despite having tough lives on the farms.
_________________________
"A government big enough to give you everything you want is a government big enough to take from you everything you have." --Gerald Ford

Top