Recent Topics
Concealed Cell Phone Permits
by Doog
2 minutes 45 seconds ago
Belgian Castrol 0w30 / 2500mi / '04 Volvo S60 2.5T
by charlesb2003
13 minutes 52 seconds ago
2013 VW GTI - Engine oil recommendation
by phem0r
20 minutes 37 seconds ago
Automotive Firmware updates - who does them?
by OVERKILL
51 minutes 39 seconds ago
what rodent starts up at 6PM to 7PM
by Donald
Today at 12:29 PM
What the heck is this?
by Jake777
Today at 11:33 AM
New Dilbert & Far Side desk calenders
by Eddie
Today at 11:26 AM
Pronto vs Napa Proselect
by mazdamonky
Today at 10:35 AM
Oreilly: QS-Advance & Microguard Special
by Greg L
Today at 10:25 AM
Oil filter, to change or not?
by otis24
Today at 10:08 AM
Changing Oil By Time Instead Of Mileage ??
by billt460
Today at 10:07 AM
OLM goes down with car sitting up?
by mobilaltima
Today at 10:03 AM
Newest Members
bspag, Lana, phem0r, 19kj57, coke
56881 Registered Users
Who's Online
81 registered (90crvtec, Andrei, 2009Edge, 440Magnum, 8 invisible), 1719 Guests and 225 Spiders online.
Key: Admin, Global Mod, Mod
Forum Stats
56881 Members
66 Forums
244505 Topics
3981923 Posts

Max Online: 2862 @ 07/07/14 03:10 PM
Donate to BITOG
Topic Options
#3305035 - 03/07/14 11:39 PM Cat 938H loader, 6.6L engine
sdan27 Offline


Registered: 06/07/09
Posts: 484
Loc: Michigan
This is a couple UOAs from a Caterpillar 938H loader we bought for our farm about a year ago. We use this loader almost exclusively to load the feed wagon for cattle. Especially this time of year, it is left to idle a lot between loads on the wagon. Using a Caterpillar 269-8325 oil filter and an LF777 bypass filter that I installed. Using Service Pro 15w-40 oil.

Unit hours 4046, 3484, 3018
Oil hours 1539, 977, 511

Fe 56, 39, 18
Cr 2, 1.7, .8
Mn .8, .4, .7
Ni .3, 0, .2
Al 3.9, 3.2, 1.4
Pb 1.3, .5, .1
Cu 6.3, 6.9, 5.6
Si 5.3, 4.6, 4.3
Na 9.7, 10, 5.2
K 0, 0, 1.1
B 2.7, 2.5, 4.6
Mo 38, 43, 38
Mg 649, 783, 712
Ca 1392, 1225, 1123
P 952, 940, 911
Zn 1238, 1244, 1037
S 1198, 2669, 3344

Soot% 1.5, 1.6, .7
Oxid 56, 56, 40
Nitr 75, 75, 50
Sulf 69, 66, 50
Visc 14.72, 14.31, 14.48
TBN 6.72, 6.49, 6.95
_________________________
'94 F250 Powerstroke. LF9691 primary oil. AH1141 air filter. FS1282, FF5320 fuel filter. WF2071 coolant filter.

Top
#3305148 - 03/08/14 05:52 AM Re: Cat 938H loader, 6.6L engine [Re: sdan27]
dnewton3 Offline



Registered: 05/14/07
Posts: 6363
Loc: Indianapolis, IN
Typical of your UOAs with Service Pro, this looks to be excellent performance.

The Fe is clearly tracking with use, and is not close to condemnation yet. All other metals are extremely low. Contamination and such all very low. TBN strong enough to not question TAN. Vis very steady with no excessive ox or nitration.

Continue use for sure.
_________________________
Conventionals vs. Synthetics isn't about which is "better"; it's about which lasts longer, while assuring safe operation, in relation to cost. Any product can be over or under utilized. The same applies to filters.
Make an informed decision; first consider your operating conditions, next determine your maintenance plan, and then pick your lube and filter. Don't do it the other way around ...

Top
#3309774 - 03/12/14 07:05 PM Re: Cat 938H loader, 6.6L engine [Re: sdan27]
dustyroads Offline


Registered: 05/13/13
Posts: 605
Loc: upstate NY
I'm always amazed how well the oil in your machinery holds up. It maintains good tbn and viscosity for long hours. I need to speak with my dairy farmer friends and neighbors about sampling and possibly extending oci's.

Thanks for posting!
_________________________
2011 Taurus sel

2013 Volvo truck with D13

Top