Search results

Hi All, I have a simple, old, nearly unmarked air compressor (with photos I'm hooping will be linked.) There's a 104 cast into the body. One of the 4 valves on the top started hissing and I can't get pressure very high. There's also oil mist leaking out. So, I'll be tearing a bit of it...

My chainsaw is fairly new, but its had issues running when warm since the 2nd or 3rd time that I've used it. Anymore, its very hard to spin the motor with the pull cord. And impossible to start it, it seems. I've attempted to ensure that there's not extra fuel in the cylinder by removing the...

Please share your advice on the following: I noticed wheel bearing play on my van, ordered bearings & seal and started pulling it apart last night. I noticed that the spindle nut was unlocked and very loose. (Note to self, check the other wheel.) The spindle now has very tiny ridges or grooves...

Sorry folks I'm back w/ the issues of this van. (96 B1500, V6)1 I thought it would be better to start a new thread than continue my stalling thread from a few weeks ago. (FYI. http://www.bobistheoilguy.com/forums/ubbthreads.php?ubb=showflat&Number=3119258#Post3119258) I would like to attempt...

I've been using my FIL's van this summer. Its got the 3.9 V-6. Lately its been stalling at idle when the transmission is engaged. It also rarely stalls when coasting to a stop. The van has 110K miles but been driven very infrequently for the past few years. I have tools and access to Chilton...

So, I did the timing belt, water pump, & engine seals this weekend on my 2000 Toyota Avalon (185K miles, 1MZ-FE engine.) To say that I’m happy with myself is an understatement. I took a couple of shortcuts to get at the oil seals. I want to ask the experienced folks here if my way of loosening...

I have 2008 Odyssey that I'm learning about. Can someone provide me with a source for a removal tool for these fasteners? http://www.amazon.com/Front-Fender-Push-Type-Retainer-91512-SX0-003/dp/B0040CVV4I I'd love to be able to quickly remove these with one hand... the old 'use 2 screwdrivers...

Hello, I'm adding a trailer brake controller on a 1996 Dodge B2500 van. I can't find the Chiltons for this model at my library... and I'm borrowing the van for a trip. Can anyone tell me the color of the wire that I should tap into for the brake signal? There's a 10-12 wire connector that plugs...

I'm borrowing a van for a trip and heard theres any issue that occurs when the fuel tank is below one-half. Basically loss of power and stumbling. So, a bad fuel pump jumps out as me. I checked out rockauto and saw a fuel inj. press. reg. exists for this too. Is either of these more likely to...

I've got a 97 Camry with an AC system that doesn't work. Its worked without fail since 97. Pressing the AC control button causes the compressor to turn for a very brief period of time followed by the apparent re-engagement of the compressor clutch. The AC indicator then starts blinking. So I...

I'd like to find a source for replacement power cords that are nearly as nice as the orig. on newer power tools. At hardware stores they only sell 6ft grounded cords with a rigid (i.e. [censored]) pvc insulator jacket. Specifically, I'm wanting to replace a cord on a 3/8 low-profile craftsman...

I've got a 2000 Toyota Avalon with 165K miles. It's been well maintained since new. It was my father-in-laws car (his first new car) and I've owned it since the odom. showed 100K. Decent oil change history. 4-6K OCIs depending on the highway usage. Ran an auto-rx dose through at 110K. Been...

I replaced all 4 struts & strut mounts on my 97 Camry last week. I got it realligned. Everything feels and sounds great with the ride. The steering does seem a little stiff. I mean a very little bit stiffer than before. There's a bit of steering memory too. The new bearings were hard to rotate...

I read about a device that can be added to cars to prevent mildew from growing on the evaporator thus causing the dreaded AC stink. Some cars, I'm told, will run the blower fan for a few minutes after turning the car off if the AC compressor has been on for a long time. A "Car care" book from...

I just fell into a formerly dormant gas trimmer. McCulloch eager beaver (400128-51). I'd love to find the starting instructions. I'm sure someone here can give me the core ideas. It has a primer, and a RUN | START| CHOKE switch. Any input on other aspects of this trimmer would be greatly...

Hi there experts and all. Here's a little issue that probably is not worth your time to read :) The thrower I have looks like this: http://cgi.ebay.com/ws/eBayISAPI.dll?Vie...bayphotohosting I got this 20+ year old Toro for free about 5 years ago. I rebuilt the carb about 5 years ago and the...

I don't have much a question here, just a few thoughts I guess. Though suggestions are welcome. I took some time to maintain my batteries recently. (Check for failing cells, trickle charge, clean or replace post clamps.) I noticed on both of my Toyotas ('97, '00 sedans) the clamps won't clamp...

My intuition tells me that running a car that has a quite drained battery does not affect how quickly the alternator wears out. I.e. a low battery can't 'break' a newer alternator. I was told the opposite recently by a non-reputable source. But, it got me thinking a bit. I certainly have a lot...

I predict this is a easy question, but who knows. My 97 Camry makes a couple of quick chirps when the power steering system is at max output and cold. I.e. when I back up and turn out of our gravel parking pad in the morning. I replaced all the belts last fall. Is the chirping most likely...

Please let me know your thoughts about this UOA. It was my first analysis on this car. I don't know if there is sludge or if the PVC valve is working. That will be a spring project for me. An even mix of city/ highway driving is common on this car. Probably a bit too much cold weather idling...